A toilet that keeps running after every flush is one of the most common household annoyances, and one of the easiest to fix yourself. That soft hiss or the tank refilling on its own in the middle of the night is water going straight down the drain, and it shows up on your bill month after month.
In this guide you will learn how a toilet tank works, how to tell which part is causing the problem, how to fix each one step by step, and when it makes more sense to call a plumber. Most repairs take less than an hour and need only a few inexpensive parts.
How a toilet tank works (in two minutes)
Lift the tank lid and you will see the whole system. Knowing what each part does makes the diagnosis much faster.
- Fill valve: the tall assembly on one side (usually the left). It lets water into the tank after a flush and shuts off when the water reaches the right level.
- Float: either a cup that slides up and down the fill valve or a ball on an arm. It tells the fill valve when to stop.
- Overflow tube: the open pipe in the middle. If the water gets too high, it spills into this tube and down into the bowl, which prevents flooding.
- Flapper: the rubber seal at the bottom of the tank. It lifts when you flush and drops back down to seal the opening.
- Chain and handle: the handle lifts the flapper through a short chain or strap.
A running toilet almost always comes down to one of two things: water is leaking past the flapper, or the fill valve is letting in too much water and it is escaping through the overflow tube.
Step 1: Find out where the water is going
Before buying anything, spend five minutes on a diagnosis.
Check the water level
Remove the lid and look at the overflow tube. If water is trickling into the top of the tube, the water level is set too high or the fill valve is not shutting off. Most tanks have a fill line marked on the inside wall; the water should stop about an inch below the top of the overflow tube.
Do the food coloring test
If the water level looks fine, the flapper is the likely suspect. The U.S. Environmental Protection Agency suggests a simple test on its WaterSense Fix a Leak Week page: put a few drops of food coloring in the tank, wait about ten minutes without flushing, and look at the bowl. If color appears in the bowl, water is leaking past the flapper. Flush afterward so the dye does not stain the tank.
Listen and watch
- The tank refills briefly every so often with nobody using it: classic slow flapper leak.
- Water runs constantly and never stops: fill valve stuck open, float set too high, or flapper not seating at all.
- The toilet runs only right after a flush and then stops on its own after a long time: chain tangled or flapper closing slowly.
Step 2: Fix the chain and flapper
Start here, because it is the cheapest and most frequent fix.
Adjust the chain
A chain that is too short holds the flapper slightly open. A chain that is too long can get trapped under the flapper. Aim for a little slack, roughly half an inch, when the flapper is closed. Move the clip to a different link on the handle arm until the flapper drops freely and closes completely.
Clean the flapper and the seat
Mineral deposits and slime on the drain opening (the flush valve seat) can stop the flapper from sealing.
- Turn off the water supply valve behind the toilet by turning it clockwise.
- Flush to empty the tank and hold the handle down to drain as much as possible.
- Wipe the rim of the opening with a non-scratch scrub pad. Avoid steel wool on plastic seats.
- Inspect the flapper. If it feels stiff, warped, cracked or slimy even after cleaning, replace it.
Replace the flapper
Flappers are sold in two common sizes, 2-inch and 3-inch, matching the size of the drain opening. Take the old one to the store or check the toilet’s model number (often stamped inside the tank) to buy the right part.
- With the water off and the tank empty, unhook the old flapper from the pegs on the overflow tube (or slide it off if it has a ring).
- Unclip the chain from the handle arm.
- Install the new flapper on the same pegs and clip the chain, leaving a little slack.
- Turn the water back on, let the tank fill, and repeat the food coloring test.
Step 3: Adjust or replace the fill valve
If water is spilling into the overflow tube, work on the fill valve.
Lower the water level
- Float cup: find the adjustment screw or clip on the side of the fill valve and turn or slide it to lower the cup.
- Float ball on an arm: turn the adjustment screw on top of the valve, or gently bend the brass arm down a little on older models.
Flush and check where the water stops. Repeat small adjustments until it shuts off below the top of the overflow tube.
Flush debris out of the valve
Sediment can keep the valve from closing. On many models you can remove the cap of the fill valve (water off first), hold a cup over the opening, and briefly turn the water supply on to flush out grit. Check the manufacturer’s instructions for your model before doing this.
Replace the fill valve
If the valve still runs, replacement is a reasonable DIY job. Universal fill valves fit most tanks and come with instructions.
- Turn off the water, flush, and soak up the remaining water with a sponge.
- Place a towel under the tank and disconnect the supply line under it.
- Unscrew the large plastic nut under the tank that holds the old valve and lift the valve out.
- Set the height of the new valve according to its instructions, insert it, and tighten the nut by hand plus a small turn. Overtightening can crack the tank.
- Attach the refill tube to the overflow tube with the included clip, reconnect the supply line, and turn the water on slowly.
- Check for drips under the tank, then set the water level.
Tools and parts checklist
- Replacement flapper of the correct size
- Universal fill valve (only if needed)
- Adjustable wrench or tongue-and-groove pliers
- Sponge, bucket and old towels
- Non-scratch scrub pad
- Food coloring for the leak test
- Rubber gloves
When to call a plumber
Most running toilets are a quick fix, but stop and get help if:
- The tank itself is cracked or leaks from the bolts after you tighten them gently.
- The water supply valve behind the toilet will not turn or leaks when you move it.
- The toilet still runs after you have replaced both the flapper and the fill valve.
- Water is leaking around the base of the toilet onto the floor.
A small leak can waste a surprising amount of water. According to the EPA, fixing easy household leaks such as worn toilet flappers can save homeowners about 10 percent on their water bills. Check your own bill before and after the repair to see the difference.
Summary
- A running toilet is usually caused by a leaking flapper or a fill valve that lets in too much water.
- Check the water level against the overflow tube, then do the food coloring test.
- Adjust the chain slack and clean the flapper seat before buying parts.
- Replace a worn flapper with one of the correct size.
- Lower the float or replace the fill valve if water spills into the overflow tube.
- Call a plumber for cracks, stuck shutoff valves or leaks at the base.
With a few minutes of diagnosis and one inexpensive part, most running toilets go quiet the same day.
Photo: Onze Woning apartment renovation, Hillegersberg, Rotterdam (2020) 96, by Donald Trung Quoc Don (Chữ HĂ¡n: 徵國單) – Wikimedia Commons – © CC BY-SA 4.0 Intern, license CC BY-SA 4.0, via Wikimedia Commons. Cropped.
